Conveyorized Rotary Arm,Ring wrapper and horizontal

• Up to 100 loads per hour *

• Min: 36”W x 36”L x 10”H
• Max: 48”W x 48”L x 80”H

• 4,000 lbs. (6,000 lbs. optional)

• 138”W X 141” L X 142”H**
  

• 3,700 lbs.

• 230V/3/60 15A (other voltages available upon request)

• 3 CFM @ 80 PSI comes with FR (Filter, Regulator)

Controls:

• Allen Bradley Micrologix 1200 PLC
• Allen Bradley AC frequency drives (except conveyors)
• 24V control system
• Current overload protection
• Nema 12 control cabinet with quick disconnect
• Autoheight sensing photoeye with on/off mode
• Power on/off lockable switch and indicator light
• 1 E-STOP mushroom type push button on the control panel and one in the wrapping zone
• Allen Bradley Touch Panel
• Variable rotary arm speed (15 RPM)
• Separate up and down carriage speeds
• Separate top and bottom wrap selection (0-9)
• Positive arm alignment controlled by proximity sensor
• Film force to load control
• Double brush dust tight slip ring
• Emergency stop sensor for arm path obstruction
• Dynamic braking system for rotary arm with AC drive
• Alarm beacon light
• Manual clamp jog
• Manual function for rotation fwd_rev. and carriage up_down
• Conveyor Jog fwd (fwd_rev optional ***)
• Intuitive alarm diagnostic on touch screen
• Reset function
• Non proprietary parts
• 120 VAC outlet in control panel for service work

• 20” Econo NO-THREAD® Powered Pre-Stretch
• 1 HP AC motor with VFD , chain & sprocket driven
• 50-300% prestretch ratio (preset to customer spec, Std 200%)
• Electronic film tension control with analog sensor
• Lexan roller cover for operator safety
• Film force release for easy pull at start and end of cycle
• Angled carriage to wrap approximately 2” from floor level
• Sensing device for film out_broken with visual alarm

• æ HP AC motor with Allen Bradley variable frequency drive
• Two #50 chain carriage lifts for safety
• Dual 1/2” CRS ways with UHMW-PE carriage glides
• Dual steel supporting boom

• Automated cut_clamp & wipe system
• Pulsed controlled cutter
• Film alignment arm
• Brush-on film tail treatment (Heat Seal available in options)

• 25” Heavy duty Ring GEAR Bearing, with Pinion GEAR Drive
• Automated lube station optional for ring gear bearing ***
• Max. 15 RPM variable speed
• 1 HP AC motor with Allen Bradley variable frequency drive
• Electronic soft start_stop
• Positive arm alignment controlled by proximity sensor
• Protection guard over the ring gear bearing
• Dynamic braking system with AC drive

• Powered process conveyor, 11 feet,6 inches long
• Standard: Pass height 18”, (other pass heights available ***)
• 3_16” wall cold rolled electric welded steel rollers
• 2 1_2” dia. rollers on 3” centers
• 52” BFR (between frame rails)
• All rollers driven via #40 chain
• 3_4 HP AC motor with contactor
• Heavy duty structural steel design
• Heavy duty cast iron flange mounted bearings
• Fix 30 FPM conveyor speed
• Additional conveyors and other types available upon request ***

• Free standing integrated 3 legs design
• Heavy duty structural steel construction
• Heavy duty safety fencing with one interlocked access door enclosing the wrapping zone
• Easy access to all components

• The machine is provided with a manual including electro_mechanical schematics and drawings
• Trouble shooting guide
• Installation instructions

• 3-year unlimited cycle warranty
• 10-year warranty on 25” ring gear bearings
• Lifetime warranty on prestretch rollers' blue compound